Rubber Cable Protector Ramp - 2, 3 & 5 Channel Cable & Hose Ramps

Running a power cable, extension lead or hose across a warehouse aisle, loading bay or event walkway creates an immediate trip hazard and a real risk of cable damage the moment a forklift, pallet truck or trolley crosses it. This rubber cable protector ramp gives you a fast, no-dig fix: cables sit inside enclosed channels beneath a hinged, high-visibility yellow lid, while the black rubber base carries the weight of pedestrian and vehicle traffic passing over the top. Interlocking end lugs let you join sections together to cover the exact run you need, and the whole ramp lifts straight back up at the end of the shift with nothing left behind.

Built to take the weight, not just cover the cable

Every section is moulded from dense black rubber with a hinged, UV-stable polyethylene lid that clips down over the cable channels rather than simply resting on top of them. That distinction matters, because a lid that lifts under a wheel stops protecting the cable and becomes a trip hazard itself. Depending on the version you choose, the ramp is rated to carry between 8 and 12 tonnes per axle, so a loaded pallet truck, forklift or small van can cross without the channels collapsing onto the cable inside. The lid is finished in high-visibility yellow with a moulded anti-slip texture, so pedestrians see the crossing point from a distance rather than finding it underfoot. Interlocking T-lugs on each end let you connect further sections in a straight run, so one order can be extended later without buying a whole new ramp.

• Vehicle-rated base – 8 to 12 tonne per axle capacity depending on channel configuration
• Hinged, clip-down lid – keeps cables fully enclosed rather than just covered
• High-visibility yellow finish – marks the crossing point for pedestrians and drivers
• Anti-slip lid texture – reduces slips for anyone walking across it
• Interlocking end lugs – join sections together to extend the run

Where it earns its keep

Site teams use it to run generator and power-tool cables across walkways on construction sites. Event crews lay it across public routes to protect stage and lighting cables from festival footfall and vehicle traffic. Warehouses and distribution centres position it at loading bays where forklifts and pallet trucks cross temporary power runs. Facilities teams reach for the smaller two-channel version indoors, in offices, retail units and exhibition halls, wherever a lead has to cross a walkway for a day, a week or a whole event run.

Base material: black rubber. Lid material: high-visibility yellow, UV-stable polyethylene with anti-slip moulded texture. Recommended maximum crossing speed: 3-5mph. Designed for temporary and semi-permanent installation, indoors or outdoors.

Choosing the right channel count

Pick the 2 Channel ramp for a single power lead or two cables run side by side where you need the highest 12 tonne axle rating in the smallest footprint. The 3 Channel ramp is the general-purpose choice, with two wider 68mm channels for power cable and a narrower 55mm channel for a second lead or a data cable, rated to 10 tonnes per axle. Choose the 5 Channel ramp when several separate cables or hoses need to cross the same route, for example a stage or generator set-up with lighting, power and signal runs together; its 8 tonne rating still covers vans, pallet trucks and most forklifts. If your crossing point is wider than one ramp, order enough sections and interlock them end to end.

Installation, use and care

Lay the ramp flat on a clean, level surface, open the lid, arrange your cables inside the channels with a little slack, then press the lid closed until the clips engage. Interlock additional sections using the end lugs for longer runs. Position speed limit signage where vehicles will cross, and keep crossing speeds to 3-5mph. After use, lift the ramp clear, wipe off grit or debris, and store flat. Rinse with water if it has been used outdoors in mud or salt.

Frequently asked questions

Can vehicles drive over this ramp? Yes, all three versions are rated for light vehicle and pedestrian traffic; check the axle weight limit for your chosen variant before HGV use.

Will the lid stay shut under traffic? The lid clips down onto the base along its hinge and is held shut by the moulded profile, so it stays closed as wheels or feet pass over it.

Can I join more than one ramp together? Yes, each section has interlocking T-lugs on both ends so you can connect as many as you need for a longer or wider crossing.

Is it suitable for outdoor use? Yes, the rubber base and polyethylene lid are weather resistant and suited to temporary outdoor installations such as building sites and outdoor events.

Ordering and delivery

Each variant is sold as a single ramp section; order multiple sections and interlock them for longer runs. See the specification table above for exact channel counts, sizes and weight ratings, and the size and fitting guide further down this page for help choosing between the 2, 3 and 5 channel versions.