Worn, rounded or polished step edges are where most stair slips start. This 55mm x 55mm GRP stair nosing caps the edge in one piece, putting a medium-grit quartz surface on both the tread and the riser. It is made for facilities managers, contractors and maintenance teams who need a stair made safe quickly, without breaking out concrete or replacing treads.
Choose from five lengths (800mm, 1000mm, 1200mm, 2000mm and 3000mm) and nine colours. The nosing fits concrete, timber, stone, tile and steel steps, indoors and out. It carries a 3-year manufacturer's guarantee against manufacturing defects, and has a design life of 10+ years depending on the traffic it carries.

Why it works
Tested grip, wet and dry
The medium-grit quartz surface was tested by the manufacturer with the pendulum method preferred by the HSE (4S slider 96). It gave readings of 79 dry, 74 wet and 61 greasy. The dry and wet results are in the top band, "extremely low slip potential" (65 and above), and the greasy result is in the "low" band (36 to 64). That matters on a stair that gets mopped, rained on or walked with wet boots, where untreated concrete or painted timber loses most of its grip.
Grit bonded in, not stuck on
GRP (glass reinforced plastic) is a fibreglass laminate, and the grit is bonded into the resin rather than applied as a tape or a coating. A self-adhesive abrasive strip lifts at the edges and wears smooth. A gritted GRP nosing keeps working as it wears, and it does not rust, rot or corrode. It works from -50°C to +80°C, so freezing external steps and warm plant rooms are both within range.
One angle covers two faces
The 55mm legs wrap the front of the step, so a crumbling concrete nose or softened timber edge is held and protected, not just patched. A stair can usually be treated in a single shift.
Where it is used
Stair nosings like this are fitted to:
- internal staircases in offices, schools, hospitals and public buildings
- external entrance steps and fire-escape routes
- steel access stairs, chequer plate and grating on plant, gantries and mezzanines
- loading docks, commercial kitchens and cold stores where footwear arrives wet
- common stairs in residential blocks, retail and transport buildings
Specifications
| Specification |
Detail |
| Material |
GRP (glass reinforced plastic) with a bonded medium-grit quartz anti-slip surface |
| Profile |
Angle section, 55mm tread x 55mm riser |
| Thickness |
Approx. 4mm |
| Weight |
Approx. 0.76kg per linear metre |
| Lengths |
800mm, 1000mm, 1200mm, 2000mm, 3000mm |
| Colours |
Yellow, White, Black, Mid Grey, Buff, Brown, Red, Blue, Green |
| Slip resistance (pendulum, 4S slider 96) |
79 dry / 74 wet / 61 greasy (manufacturer's test, July 2016) |
| Light reflectance value (LRV) |
White 79.9, Yellow 48.7 (other colours not published) |
| Service temperature |
-50°C to +80°C |
| Fixing method |
Screw-fix, adhesive, or both (both recommended) |
| Suitable substrates |
Concrete, timber, stone or tile, metal, steel, chequer plate, grating |
| Location |
Internal and external |
| Building Regulations |
55mm on both tread and riser, the minimum width in Approved Document K, clause 1.7a |
| Guarantee |
3-year manufacturer's guarantee: free replacement for any manufacturing defect within 3 years of purchase |
| Design life |
10+ years, depending on the type and volume of traffic |
Choosing the right length and colour
Length: measure the full width of each tread and buy the next length up. Trimming 60mm off a 1200mm nosing is better than leaving 40mm of the step edge unprotected. Use the 2000mm and 3000mm lengths for wide flights, or cut them down across several narrower treads to reduce waste.
Colour: first decide whether the nosing needs to mark the step edge or blend in. Approved Document K asks for step nosings in buildings other than dwellings to contrast visually and to be at least 55mm wide on both tread and riser. This profile meets that width. Approved Document M treats a difference of more than 30 LRV points as adequate contrast. Yellow (48.7) and White (79.9) stand out clearly against dark or mid-grey steps, and Buff does the same on darker concrete. Black, Mid Grey and Brown suit timber or dark treads where the job is edge protection. Red, Blue and Green are used for colour-coding routes, floor levels or plant areas.
Installation, use and care
The step must be sound and flat, so fill any damage or dips first. For adhesive, the surface must also be clean and dry. Dry-fit each nosing before you fix it. Then:
- Run a 6mm bead of high-strength polyurethane adhesive around the perimeter of the underside. One 300ml tube bonds about 5 linear metres.
- Bed the nosing in with hand pressure.
- Fix with stainless steel self-tapping screws about 50mm in from each end, then at no more than 250mm centres.
Screw-fixed stairs can be used immediately. Adhesive-only stairs reach full bond in about 48 hours at 23°C. On wet or oily steps, always use screws.
Cutting: use an angle grinder with a stone or diamond blade, outdoors or with dust extraction, while wearing eye and respiratory protection.
Cleaning: a stiff brush, or mild detergent and warm water.
Inspection: check the fixings monthly on high-traffic stairs.
Frequently asked questions
Will a 55mm x 55mm nosing suit my steps?
It suits any step with a reasonably square front edge and at least 55mm of usable tread and riser at the nose. On a rounded or badly broken edge, fill and level the edge first, or the nosing will rock on the high points.
What slip resistance does it achieve?
The manufacturer's pendulum test (4S slider 96) gave 79 dry, 74 wet and 61 greasy. The dry and wet readings are in the extremely low slip potential band (65 and above). The greasy reading is in the low band (36 to 64).
Can I cut it to length on site?
Yes. Use an angle grinder with a stone or diamond blade, wearing eye and respiratory protection. A jigsaw or hacksaw handles small trims and cut-outs.
Is it suitable for outdoor steps?
Yes. GRP does not rust or rot, and the nosing works from -50°C to +80°C. Outdoors, use adhesive as well as screws, because the adhesive also seals the edges and stops water sitting under the nosing.
What fixings and adhesive do I need?
Use stainless steel self-tapping screws about 50mm in from each end and then at no more than 250mm centres, plus a high-strength polyurethane adhesive. One 300ml tube covers about 5 linear metres.
Ordering and delivery
Choose the length first, then the colour, and set the quantity to the number of steps. For example, 10 steps at 1000mm wide means 1000mm with a quantity of 10. Add each length or colour separately. UK mainland delivery is a single flat rate however many pieces you order, so order the whole flight at once. For a length or colour that is not listed, contact us before ordering.
Also in the range: GRP stair tread covers, 345 x 55mm, heavy duty GRP stair nosings and the 70 x 30mm GRP nosing for shallower risers.
View our complete range of stair nosing profiles, with aluminium, rubber and PVC options for every application.