What are 19mm Anti-Slip Strips?

These narrow pre-cut self-adhesive anti-slip strips are specifically sized for the surfaces where conventional wider tape is impractical — ladder rungs, narrow stair nosings, vehicle step plates, access platforms, and any surface where a 50mm or wider strip would overhang or appear disproportionate. At 19mm wide and 610mm long, each strip sits neatly on a standard ladder rung or across a narrow step edge, providing targeted anti-slip grip exactly where it is needed.

Each pack contains 10 individually cut strips — the right quantity for a complete fixed ladder (most have 8–15 rungs), a partial staircase, or a set of vehicle steps. The coarse silicon carbide grit surface delivers the same grip performance as a full-width anti-slip tape, concentrated on the narrow surface area where most slips occur on ladders and narrow steps. Peel the backing from each strip, press firmly onto the rung or step, and it is immediately ready for use.

Technical Specifications

Key Features and Benefits

• Sized for ladder rungs — at 19mm wide, these strips fit neatly on standard metal ladder rungs without overhanging the sides. A single strip per rung provides targeted grip on the surface that hands and feet actually contact.
• Pack of 10 — right quantity for a complete ladder — most fixed access ladders have 8 to 15 rungs. A single pack covers a complete ladder, leaving spares for future replacement. No need to cut from a roll and waste material.
• Pre-cut to 610mm — standard ladder and stair width — 610mm covers a standard UK domestic staircase and most fixed access ladder widths. Simply peel and press — no measuring or cutting required.
• Silicon carbide grit — maximum grip on narrow surfaces — on ladder rungs and narrow step edges, the grit surface is what stands between a secure foothold and a slip. Coarse silicon carbide provides the most aggressive grip available in this format.
• Waterproof and UV stable — performs on outdoor ladders, roof access, marine equipment and any external installation where rain and UV exposure would degrade inferior alternatives.

Where to Use

• Fixed access ladders — loft hatches, roof access, plant room ladders, mezzanine ladders
• Portable ladders — step ladders, extension ladders, scaffold ladders
• Vehicle step plates — lorry and van cab steps, horse trailer steps, motorhome steps
• Narrow stair nosings — step edges too narrow for full-width tape
• Boat and marine ladders — boarding ladders, engine room access, marina dock ladders
• Scaffolding access — scaffold board edge anti-slip on narrow access boards
• Playground and gym equipment — climbing frame rungs, gym ladder rungs

How to Apply

1. Clean the rung or surface. Degrease metal rungs with isopropyl alcohol. Remove all grease, oil and dirt. Allow to dry completely.
2. Position the strip. Place the strip on the rung without peeling the backing to check alignment. Centre it across the rung width.
3. Peel the backing. Peel the release liner from the back of the strip.
4. Press firmly. Press the strip onto the rung with thumb pressure, starting from the centre and working outward to avoid air bubbles.
5. Apply sustained pressure. Hold the strip down firmly for 30 seconds to seat the adhesive fully.
6. Repeat for each rung. Work from the bottom rung upward for the most efficient installation sequence.

Frequently Asked Questions

Will one pack cover a full ladder?

A pack of 10 strips covers most fixed access ladders, which typically have 8 to 12 rungs. For taller ladders with more rungs, two packs provide comfortable coverage. The 610mm length suits ladder widths up to approximately 600mm.

Can I cut the strips shorter for narrower rungs?

Yes. The strips cut cleanly with scissors at any point along their length. For narrower ladder rungs or step plates, simply cut to the required length.

Do they work on round metal rungs?

Yes. The strip's pressure-sensitive adhesive bonds to the upper surface of round metal rungs. For maximum adhesion on round rungs, apply with firm thumb pressure working from the centre outward, pressing the strip down onto the curved surface. The strip will conform to a slight curvature.

How long do they last on external ladders?

On external metal ladders in normal UK weather conditions, expect 1–3 years before replacement is needed. For maximum longevity on outdoor metal ladders, ensure the rung is thoroughly degreased and dry before application, and apply in dry conditions above 10°C.

Why Buy From Stair Nosings UK?

• Safety accessories specialist with a complete range for every slip hazard application
• Coarse silicon carbide grit — higher performance than budget alternatives
• Pack of 10 — the right quantity for a complete ladder installation
• UK stock for fast dispatch

One pack — 10 strips — covers a complete access ladder. Order now for immediate dispatch.