Solid Oak Stair Nosing - Bullnose Trim for 14mm & 20mm Wood Floors

A stair edge finished in printed laminate or painted softwood looks wrong the moment it sits next to a real wood floor, and it's usually the first place a staircase starts to look tired. Solid oak stair nosing carries the same timber, grain and colour straight over the front of every tread, so the join between floor and step disappears instead of standing out. It is machined from a single piece of oak rather than a wood-effect laminate, which means it ages, sands and refinishes exactly like the rest of an oak floor.

Why solid timber outperforms laminate nosing

Laminate and foil-wrapped nosings are a thin decorative layer over MDF or softwood core, so once that layer chips or wears through on a heavily used step, the repair is visible forever and the whole piece has to be replaced. This nosing is solid oak from face to fixing groove, so surface wear, a dropped tool or a dog's claws take off oak, not printed film. Because the timber runs all the way through, you can sand out light scuffs and re-lacquer or re-oil the profile in place, the same maintenance any oak floor already gets. The 14mm and 20mm rebate options are milled to sit directly over the matching engineered oak floor thickness, so the nosing sits flush with the tread rather than creating a lip that catches a heel or a hoover. Every piece is supplied with the fixing groove pre-cut, ready to glue and pin to the stair carcass.

• Solid oak core – wears, sands and refinishes like the rest of the floor, not a laminate skin
• Flush-fit rebate – 14mm or 20mm depth matched to your engineered oak floor thickness
• Bullnose profile – rounded front edge is safer underfoot than a square laminate lip
• Pre-cut fixing groove – glues and pins directly to the stair carcass, no extra jointing
• Colour-matched finishes – lacquered, unfinished or smoked to suit an existing oak floor

Where it's used

This nosing finishes the leading edge of stair treads wherever an engineered or solid oak floor continues up a staircase, most commonly in hallways, landings and open-plan stairs in UK homes. It also finishes single raised steps between rooms, mezzanine edges and short flights in extensions, so the flooring reads as one continuous surface rather than stopping abruptly at the change of level.

Specifications

Choosing the right option

Match the rebate depth to your floor first: 14mm nosing is for 14mm engineered oak boards, 20mm nosing for 20mm engineered or solid boards. Fitting over a different thickness leaves a step or a gap at the tread edge, so check your flooring's stated thickness before ordering rather than the finished plank width. For finish, lacquered suits a floor that is already satin-lacquered from the same range; unfinished is the right choice if you plan to site, stain or oil the nosing to match a bespoke floor colour once fitted; smoked and smoked-and-white-oiled are pre-toned to match fumed and whitewashed oak ranges without further finishing. Use the 0.9m length for a single standard UK stair tread and the 2.35m length for wide stairs, landings or where you are fitting several short pieces from one board to reduce joins.

Installation, use & care

Cut to length with a fine-tooth saw, test-fit the rebate over the tread edge, then fix with a flooring adhesive suited to solid wood and pin through the top face into the tread below, punching and filling the pin holes before finishing. Unfinished nosing should be sanded flush with the adjoining floor before staining or oiling so the sheen matches. Clean with a barely damp cloth and a wood-safe floor cleaner; avoid saturating the joint line with water, which is the main cause of a nosing lifting over time. Re-lacquer or re-oil on the same cycle as the rest of the floor to keep the colour consistent.

FAQ

Will the unfinished nosing match my existing lacquered oak floor?
Not until it's finished. Sand it flush, then apply the same lacquer or oil and number of coats used on your floor so the sheen and tone match once cured.

Can I fit this over a laminate or LVT floor instead of real wood?
No. This is a solid timber profile sized to oak floor thicknesses; laminate and LVT stairs need a nosing designed for those thinner, harder-wearing surfaces.

What if my stair tread is wider than 2.35m?
Order two lengths and join them with a neat butt joint positioned away from the most heavily walked centre of the tread, then fill and finish the joint to disguise it.

Does the smoked finish fade in sunlight?
All timber finishes will mellow slightly with UV exposure over years, the same as any oak floor near a window; this is a natural, gradual colour change rather than a defect.

Ordering & delivery

Choose your rebate thickness, finish and length above; each variant is priced and stocked individually. Pieces are supplied straight and ready to cut on site. See the specification table and size and fitting guide further down this page before ordering if you are unsure which thickness matches your floor.